Site Logotype

Non Invasive Treatment

Plasma Skin Tightening is a revolutionary, non-invasive alternative treatment to traditional surgery. The treatment helps eliminate excessive tissue that causes sagging skin, unwanted wrinkles, stretch marks and even diminish scarring. It also diminishes the risk, pain and down-time associated with traditional invasive  surgery.

 

“The Fibroblast Skin-Tightening treatment is a completely non-invasive, non-surgical procedure, where no scalpels or any surgical instruments are used. This treatment is an active answer to the client’s needs for beauty treatments that provide a perfect look but are not based on surgical methods.”

How it Works

“The Fibroblast Skin-Tightening treatment is a completely non-invasive, non-surgical procedure, where no scalpels or any surgical instruments are used. This treatment is an active answer to the client’s needs for beauty treatments that provide a perfect look but are not based on surgical methods.”

Plasma is often referred to as “the fourth state of matter”, after solid, liquid, and gas. It is created when electrostatic energy mixes with ionized gas. When the thermal energy from a plasma device reaches around 1mm from the skin, it mixes with oxygen and nitrogen in the atmosphere and creates a plasma arc, which vaporizes upon contact with the skin.​

Treats A Wide Range Of Areas

FDA Registered

(FDA CLASS 1 Registered Device)

Plasma Fibroblast skin tightening treatments lift and tighten the skin by activating your fibroblast cells using our FDA Class I Plasma Pen Device .

These cells can be found in the dermis. The reason why this works so well for anti-aging efforts is that fibroblast cells can create high levels of collagen and elastin. You may have already heard a lot about collagen and elastin as they are responsible for tightening your skin and keeping it youthful. Once you have high levels of collagen and elastin, you will begin seeing long-term skin tightening effects .

The fibroblast treatment device uses voltage in the air and the gases that come from our skin to create a plasma charge. An electrical arc is made to reduce any extra skin it is targeted at. Your skin tissue will then shrink and tighten to create an anti-aging effect.

Before / Afters

FAQ

Does plasma (fibroblast) skin tightening hurt? Low levels of discomfort have been reported by patients during and after the treatment. Before the treatment, a topical numbing cream will be applied to the targeted skin. The discomfort you feel will not compare to surgical solutions. You can go back to your daily routine right after treatment as it doesn’t damage deep skin layers.

Your skin will be red and slightly swollen for up to 3 days. The tingling or burning sensation you may feel can be treated by an ice pack / aftercare product . The burning sensation should feel similar to a sunburn.Minimal redness may be seen up to 3 weeks after the treatment. Carbon crusts will form and darken where the fibroblast treatment tool is applied. Refrain from touching carbon crusts for 5-10 days after your treatment

You will probably be able to see a slight difference directly after your treatment. You will see full results 8 weeks after your treatment as the Fibroblast takes time to produce collagen type lll and eventually convert it to Type I collagen which is the targeted outcome. In most cases , clients are happy after 2 to 3 treatment sessions depending on the area you wish to tighten.

Your session could take anywhere from 45 minutes to 120 hours
It all depends on the area you are targeting. For instance , both eyelid area would require approx an hour.

The effects are expected to stimulate fibroblast production for up to 1 year after treatment .

Yes, a fibroblast treatment is safe. It is nonsurgical and has a low number of side effects. Healing time is fairly low and your results are long-lasting. The main side effects are a burning sensation after treatment and carbon crusts around the area.arbon crusts (the dots around the targeted area) should be left alone for the next week or so.

It is highly important to take note that after treatment direct contact with sun rays (UV radiation) and the use of chemical products on the treated area should be avoided. SPF (Sun Protection Factor) is of key importance and an essential part of aftercare. The most important step you need to take to prevent hyperpigmentation is sun protection. The sun’s rays affect the skin even when it is cloudy outside, so it is important to provide daily protection for the skin. The treatment comes with Aftercare products .

 

Aftercare is one of the most important parts of the treatment. Each client has to follow the instructions for aftercare closely to achieve the perfect results:

Do not cover with plasters, the superficial wound needs oxygen to form carbon crust.

First 24 h after Plasma-Fibroblast treatment use After Care #1 in the spray. Spray the area 3-4 times a day.

TIP: Do not wash the treated area first 24h!

Do not pick carbon crust, it will fall off in a few days, usually 4-6th day.

Use the After Care #2 cream after the first 24 h. Keep using After Care #2. as long there is any visible traces of redness, irritation. After Care #2 should be used at least 2-3 weeks.

 When you are exposed to the sun, use After Care #3 cream as it is UV protect and protects the treated area.

Avoid sauna, pools or any kind of exposure to activities which present the risk for infection of the treated area.

Make sure to protect the treated area from direct sun until the skin is completely regenerated (5–6 weeks). The more you keep off the sun better it is for the treated area

Do not apply products containing alcohol or other scents.